Getting Familiar with Plumbing: Before Installing a Bathtub
Getting Familiar with Plumbing: Before Installing a Bathtub
Blog Article
Just about every person maintains their own unique notions in relation to Installing A Bathtub.
Setting up a bath tub isn't exactly brain surgery, but it does need strong plumbing, woodworking, and occasionally, tiling skills. Replacing an old tub with a brand-new one is also a moderately hard project. If the old bathtub is readily obtainable, the job can relocate quickly; if you need to open a wall surface to get rid of the old tub and also position the new bath tub, the task is much harder. In either instance, the task is within a home handyman's abilities, although you will certainly need an assistant to move out the old bathtub and also set in the brand-new one. Ensure you have certified on your own for the task and fit trying it. Instead of hiring a professional to take control of a halfway-completed task, it is much better to consider using one before you start. Possibilities are you may require a professional plumber to make tube links.
This article will certainly help you mount a new tub in your bathroom if you have currently purchased a brand-new bathtub and do not require to change the plan of your previous water supply pipes.
Your devices and also material checklist must consist of the following:
Planning for the Installation
Firstly, the supporting frame provided with the bathroom should be fitted (if required) according to the maker's directions. Next, fit the taps or mixer to the bath tub. When fitting the tap block, it is necessary to ensure that if the tap comes with a plastic washer, it is fitted between the bathroom and the taps. On a plastic bathroom, it is likewise practical to fit a sustaining plate under the faucets device to prevent pressure on the bath tub.
Fit the flexible faucet ports to the bottom of both taps using 2 nuts as well as olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet via the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Make certain you use every one of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath ought to now prepare to be fitted in its final placement.
Removing Old Touches
If you require to change old faucets with new ones as a part of your installation, after that the first thing you should do is detach the water system. After doing so, activate the faucets to drain pipes any type of water remaining in the system. The process of eliminating the existing faucets can be fairly problematic due to the restricted gain access to that is usually the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the faucets. Have a towel all set for the continuing to be water that will certainly originate from the pipes. When the supply pipes have been removed, make use of the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from transforming during this process. As soon as the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned of any kind of old sealing substance.
Prior to proceeding to fit the new faucets, compare the pipeline connections on the old faucets to the new taps. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Mounting the Bathtub
Making use of both wooden boards under its feet, place the bathtub in the needed setting. The wood boards are valuable in equally spreading the weight of the tub over the area of the boards rather than focusing all the weight onto four little factors.
The next goal is to ensure that the bath tub is leveled all round. This can be accomplished by inspecting the spirit level and also changing the feet on the bathtub till the spirit level reviews level.
To install faucets, fit all-time low of the furthest versatile faucet connector to the proper supply pipe by making a compression join; then do the very same for the other tap.
Turn on the water system as well as inspect all joints as well as new pipework for leakages and also tighten them if essential. Fill up the tub and additionally examine the overflow electrical outlet and the typical electrical outlet for leaks.
Finally, deal with the bathroom paneling as defined in the producer's user's manual. Tiling as well as sealing around the bathtub must wait up until the tub has actually been used a minimum of when as this will resolve it right into its last placement.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic port to avoid damage to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the other end supplies a link to the current supply pipes.
If you need to fit a monobloc, after that you will certainly require lowering couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, place the tap in the mounting opening in the bath/basin ensuring that the washers are in location between the faucet and the sink. Safeguard the faucet in position with the maker supplied backnut. Once the faucet is safely in position, the supply pipes can be connected to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular faucet connectors. The previous kind should be connected to the tap finishes initially, tightening just by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the area where the bath meets the tile, it is required to seal the accompanies a silicone rubber caulking. This is important as the installation can relocate sufficient to fracture a stiff seal, triggering the water to pass through the wall surface between the bathroom and the tiling, causing problems with wetness as well as possible leakages to the ceiling below.
You can pick from a variety of coloured sealers to blend in your fixtures and also fittings. They are marketed in tubes and cartridges, as well as can sealing spaces approximately a width of 3mm (1/8 inch). If you have a larger space to load, you can fill it with twists of drenched paper or soft rope. Bear in mind to always fill up the tub with water prior to securing, to permit the activity experienced when the tub is in usage. The sealer can split fairly early if you do not take into consideration this activity before sealing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise quickly available on the market. It is advisable to fit the floor tiles utilizing water-resistant or waterproof glue and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm just very curious about How to Install a Bathtub and I am hoping you liked our entry. Sharing is caring. Who knows, you may very well be doing someone a favor. I love reading our article about Tools You Need to Install a New Bathtub .
Call now! Report this page