GETTING FAMILIAR WITH PLUMBING: YOUR STARTING POINT FOR WHEN INSTALLING A BATHTUB

Getting Familiar with Plumbing: Your Starting Point for When Installing a Bathtub

Getting Familiar with Plumbing: Your Starting Point for When Installing a Bathtub

Blog Article

Get A Free Estimate

This post which follows relating to Tools You Need to Install a New Bathtub is really compelling. Give it a try and draw your own personal assumptions.


A Step-by-Step Guide to Installing a Bathtub
Mounting a bathtub isn't specifically brain surgery, but it does call for strong plumbing, woodworking, and in some cases, tiling abilities. Replacing an old bathtub with a new one is also a moderately tough project. If the old tub is easily obtainable, the project can relocate rapidly; if you have to open a wall surface to remove the old bathtub and place the new tub, the job is a lot harder. In either instance, the project is within a home handyman's abilities, although you will need a helper to leave the old bathtub and set in the brand-new one. Make sure you have actually certified on your own for the task as well as fit attempting it. As opposed to hiring a specialist to take control of a halfway-completed job, it is much better to consider utilizing one before you begin. Possibilities are you might require a professional plumber to make tube links.
This short article will certainly aid you mount a new tub in your restroom if you have actually currently gotten a new tub as well as don't require to change the setup of your previous water pipelines.
Your tools as well as product checklist need to make up the following:
  • New Bathtub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Blade

  • Tape Measure

  • Pipe Caps


  • Planning for the Installment


    To start with, the sustaining structure supplied with the bath must be fitted (if required) according to the producer's directions. Next off, fit the faucets or mixer to the bathtub. When suitable the tap block, it is very important to make sure that if the tap features a plastic washing machine, it is fitted in between the bath and the faucets. On a plastic bathroom, it is additionally practical to fit a supporting plate under the taps device to avoid pressure on the bathtub.
    Fit the flexible tap adapters to the bottom of both faucets using 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet through the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next off, fit the end of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Make sure you utilize every one of the supplied washing machines.
    Connect the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom should now be ready to be fitted in its last setting.

    Removing Old Touches


    If you require to change old taps with brand-new ones as a part of your installation, then the first thing you need to do is disconnect the supply of water. After doing so, switch on the faucets to drain any kind of water remaining in the system. The process of eliminating the existing taps can be quite bothersome due to the restricted access that is often the instance.
    Utilize a container wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipelines to the taps. Have a cloth ready for the continuing to be water that will originate from the pipes. As soon as the supply pipelines have actually been eliminated, utilize the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the single taps from transforming throughout this process. As soon as the taps have actually been removed, the holes in the bath/basin will certainly need to be cleaned up of any old sealing substance.
    Prior to going on to fit the new faucets, contrast the pipe links on the old faucets to the brand-new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the brand-new faucets to fit.

    Mounting the Bathtub


    Making use of the two wood boards under its feet, put the tub in the required placement. The wood boards are practical in evenly spreading out the weight of the tub over the location of the boards as opposed to concentrating all the weight onto four little factors.
    The following goal is to ensure that the bath tub is leveled all round. This can be accomplished by inspecting the spirit level and changing the feet on the bath tub until the level checks out level.
    To install faucets, fit all-time low of the outermost versatile tap port to the suitable supply pipe by making a compression sign up with; then do the same for the other tap.
    Turn on the water as well as inspect all joints and brand-new pipework for leakages and tighten them if necessary. Fill the bath tub and likewise examine the overflow outlet and the typical outlet for leaks.
    Lastly, deal with the bathroom paneling as defined in the maker's instruction manual. Tiling and sealing around the bathtub must wait up until the bath tub has been used at the very least when as this will certainly resolve it into its last setting.

    Suitable New Taps


    If the tails of the new taps are plastic, then you will certainly require a plastic port to prevent damage to the string. One end of the adapter fits on the plastic tail of the tap as well as the various other end supplies a link to the existent supply pipelines.
    If you require to fit a monobloc, then you will call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
    Next off, place the tap in the installing opening in the bath/basin making sure that the washers are in location in between the faucet and the sink. Protect the faucet in place with the producer provided backnut. When the tap is firmly in place, the supply pipes can be linked to the tails of the taps. The taps can either be linked by using corrugated copper piping or with typical tap connectors. The former type must be attached to the tap ends first, tightening only by hand. The supply pipes can later be linked to the various other end. Tighten both ends with a spanner after both ends have been attached.

    Tiling Around the Bath tub


    In the location where the bath fulfills the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is necessary as the installation can move enough to break an inflexible seal, triggering the water to pass through the wall between the bath as well as the tiling, leading to issues with dampness and feasible leakages to the ceiling below.
    You can choose from a selection of coloured sealants to blend in your fixtures and also fittings. They are offered in tubes and also cartridges, and also are capable of sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with twists of soaked paper or soft rope. Bear in mind to constantly load the bath tub with water before sealing, to enable the movement experienced when the tub is in use. The sealant can break fairly very early if you do not consider this motion before sealing.
    Alternatively, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally conveniently offered on the market. It is suggested to fit the tiles using water-resistant or water resistant glue as well as cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub Yourself

    We hope you enjoyed reading our piece about A Step-by-Step Guide to Installing a Bathtub. Thanks a ton for taking the time to browse our blog. Enjoyed our blog entry? Please share it. Help other people check it out. We treasure reading our article about A Step-by-Step Guide to Installing a Bathtub.


    Problem? Dial now!

    Report this page